Wiki source for ET9x00Flash
====Xtrend ET9x00====
==={{color c="gray" text="Flash an image via USB"}}===
It is very simple to flash your Xtrend ET9X00 receiver using an USB stick. Just follow these instructions: Download and unzip the file from http://openpli.org/download/xtrend/et9x00/.
1) Copy the folder on an FAT32 formatted USB-Device and plug it in before booting.
1) Unzip compressed file.
1) Copy the "ET9000" folder to a USB Pen Drive.
1) Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
1) Power on receiver with the mains switch on the rear.
1) After rebooting or cold start a message like 'image found, press ok' appears on the screen.
1) After pressing 'ok' a message appears 'Update in progress'.
1) After the update is ready the receiver will reboot automatically.
1) You could remove the USBstick first or you just wait.
1) Follow the procedure on the screen.
1) After making the right choices your box will be ready with new firmware.
In case you have made a backup with the Autobackup plugin, the procedure is as follows.
1) After you have downloaded and unpacked an image go to 2
1) Put the USB stick into the front USB input.
1) You'll see a message on the screen like 'no plugins found'.
1) Go to menu - plugins - autobackup and change 'Backup location'to media/usb.
1) Change 'Create Autoinstall' to 'on'.
1) Press the yellow key for a manual backup on the USBstick.
1) After the backup has finished push the green key and leave the menu.
1) Reboot the box and follow this procedure.
1) After rebooting or cold start a message like 'image found, press ok' appears on the screen.
1) After flashing the image, the box reboots and if you won't do anything, the box reinstalls completely like it was before.
----[[HomePage Back to the PLi® Wiki]] : [[DM500 DM500]] : [[DM500plus DM500+]] : [[DM56xx DM56xx]] : [[DM600 DM600]] : [[DM7000 DM7000]] : [[DM7020 DM7020]] : [[DM7025 DM7025]] : [[DM800 DM800]] : [[DM8000 DM8000]]
==={{color c="gray" text="Flash an image via USB"}}===
It is very simple to flash your Xtrend ET9X00 receiver using an USB stick. Just follow these instructions: Download and unzip the file from http://openpli.org/download/xtrend/et9x00/.
1) Copy the folder on an FAT32 formatted USB-Device and plug it in before booting.
1) Unzip compressed file.
1) Copy the "ET9000" folder to a USB Pen Drive.
1) Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
1) Power on receiver with the mains switch on the rear.
1) After rebooting or cold start a message like 'image found, press ok' appears on the screen.
1) After pressing 'ok' a message appears 'Update in progress'.
1) After the update is ready the receiver will reboot automatically.
1) You could remove the USBstick first or you just wait.
1) Follow the procedure on the screen.
1) After making the right choices your box will be ready with new firmware.
In case you have made a backup with the Autobackup plugin, the procedure is as follows.
1) After you have downloaded and unpacked an image go to 2
1) Put the USB stick into the front USB input.
1) You'll see a message on the screen like 'no plugins found'.
1) Go to menu - plugins - autobackup and change 'Backup location'to media/usb.
1) Change 'Create Autoinstall' to 'on'.
1) Press the yellow key for a manual backup on the USBstick.
1) After the backup has finished push the green key and leave the menu.
1) Reboot the box and follow this procedure.
1) After rebooting or cold start a message like 'image found, press ok' appears on the screen.
1) After flashing the image, the box reboots and if you won't do anything, the box reinstalls completely like it was before.
----[[HomePage Back to the PLi® Wiki]] : [[DM500 DM500]] : [[DM500plus DM500+]] : [[DM56xx DM56xx]] : [[DM600 DM600]] : [[DM7000 DM7000]] : [[DM7020 DM7020]] : [[DM7025 DM7025]] : [[DM800 DM800]] : [[DM8000 DM8000]]
